Pace-by-Step Instructions for Cleaning a Water Softening Brine Tank

How to Clean Water Softener Brine Tank

When was the last time you lot cleaned your water softener's brine tank?

Yes, cleaning your softener'southward brine tank is right at the height of your "Weekend Fun Activeness" list, correct? The good news is, a brine tank just needs to be thoroughly cleaned once each yr–and information technology's really not hard. We'll take y'all through the 12 like shooting fish in a barrel steps to clean a h2o softener brine tank.

Kickoff, one quick disclaimer: Some of the softening common salt pellets sold at the supermarket or home comeback store are "evaporative table salt pellets" that contain a loftier level of water-insoluble matter or impurities. This insoluble matter can cause buildup in the reservoir or crusade your softener to malfunction. If yous notice buildup, the brine tank will need to exist cleaned more oftentimes than in one case annually. And so when you shop for softening table salt, look for labeling on the salt pellet sack that indicates y'all're getting the highest purity level.

Footstep-by-Step Instructions for Cleaning a Alkali Tank

  1. Follow your system's manufacturer instructions for putting the system in "Bypass Mode". This way, water will bypass the softener for a short menses of time and so that cleaning can be done.

  2. Disconnect all lines/hoses between the water softener and brine tank.

  3. Siphon or dump water out of the alkali tank (not on grass or plants as the loftier percentage of sodium in this water/common salt mixture may injure lawn or plants).

  4. Take out any remaining salt and discard.

  5. If the brine tank has a salt span (one big block of salt), you'll need to use warm or hot water to loosen the salt span upwardly and intermission it out.

  6. Pull the "brine filigree" out if there is 1. A alkali grid is the platform/screen at the bottom of a brine tank. Not all brine tanks have a brine filigree.

  7. Cascade a few tablespoons of  dish lather into 1-2 gallons of water to create a soapy mixture.

  8. Pour the lather/water mixture into the brine tank and scrub the within with a long-handled brush. Dump and rinse with water.

  9. At present pour two-3 gallons of make clean water into the brine tank with a quarter cup household bleach. Stir and permit the bleach/water solution sit for 15 minutes.  Scrub the inside of tank with a brush and chlorine water.

  10. Dump and rinse the bleach h2o.

  11. Put brine tank back in place and connect all lines to h2o softener and drain. Take the system out of "Bypass Fashion".

  12. Put 5 gallons of make clean water into the brine tank.

  13. Lastly, add together water softener salt to the brine tank–at least two 50-lb bags.Nosotros recommend keeping the brine tank at least ane quarter full of water softener salt at all times. For best results, don't fill table salt to the very top of the brine tank, but leave six inches of space from the peak rim of the tank.

In the future as you replace table salt in the brine tank, make sure the salt level always remains a few inches above the water level. And before adding new salt pellets, always make sure to loosen upward any encrusted salt that may be sticking to the edges of the tank and break up whatsoever big pieces of salt.

Keep in mind that the salt will need a little time to sit in the brine reservoir and begin dissolving earlier regeneration tin can occur (about 2 hrs).  When one immediately initiates regeneration after adding salt to the brine tank, the water softening resin may not exist sufficienly cleaned in the regeneration process.

If you lot have followed the above steps and water softening does not take place, it could indicate the softener is malfunctioning or there's a problem with the table salt you're using. Not certain if your water softener is working properly or fully softening your water? Contact a local authorized WaterTech dealer and accept your system thoroughly checked out.

find a watertech dealer